These portable dispensing systems cool the beer as it travels through a cold plate that is covered in ice. The cold plate has two 304 gauge stainless coils encased in aluminum for easy cleaning and sanitation. Make sure to run beer through the line before you add ice to avoid freezing the lines. The cooler is only available in blue, and some as...

http://www.midwestsupplies.com/commercial-sanke-draft-box.html

Looking to build your own jockey (draft) box, but don't know what to use to chill the beer with? The Single Line Cold Plate is a great option. The aluminum housing lets the beer flow through 18 gauge stainless steel product line. The beer goes in warm, and comes out cold. You also get the barbs and o rings with this very low profile plate. The l...

http://www.midwestsupplies.com/cold-plates-single-line.html

This is just the Compact CO2 Injector. You do not get a gas fitting when you purchase this unit. Perfect for those that already have threaded gas fittings for their kegs. Note: Uses only Genuine Innovations 16 gram CO2 cartridges. Note: Models purchased before January, 2006 require 12g CO2 cartridges. Compact CO2 Injector Only. Use...

http://www.midwestsupplies.com/compact-co2-injector-only.html

Pass Through Shanks are just that, a pass through. They are a way to securely attach your tubing with a clean, professional look. Drill a 1" hole into the back of a cooler, insert the shank, and use the 2 attached nuts to tighten up the shank to the cooler. Do forget, you are going to need hex nuts, tail pieces, washers, tubing, and clamps t...

http://www.midwestsupplies.com/pass-through-shank.html

Connects a Keg Coupler to the back end of the Commercial Sanke Draft Box. Comes with 5' of 3/8" ID tubing, Two Hex Nuts and Neoprene Washers.

http://www.midwestsupplies.com/jumper-line-5-for-sanke-draft-box.html

This is a replacement Cold Plate Fitting for the "Out" side of the cold plate. This fitting comes threaded to screw into the cold plate, and the other side has a 1/4" barb to attach your tubing to.

http://www.midwestsupplies.com/cold-plate-fittings-out-1-4-barb.html

A shank doesn't do you much good without a Chrome Coupling Nut to help you attach your tap to your shank. A "Shank Securing Wrench can make installing and removing the faucet disconnect much easier.

http://www.midwestsupplies.com/chrome-coupling-nut-faucet-disconnect.html

A shank doesn't do you much good without a Brass Coupling Nut to help you attach your tap to your shank. A "Shank Securing Wrench can make installing and removing the faucet disconnect much easier.

http://www.midwestsupplies.com/brass-coupling-nut-faucet-disconnect.html

Neoprene Washers are used with a Hex Nut or Wing Nut and Tail Piece when attaching to a shank or coupling for a leak-proof seal.

http://www.midwestsupplies.com/neoprene-washer.html

The O-ring for a Cold Plate Fitting is very small, and very easy to lose. Make sure you are never without your jockey box by having extra's of these at home.

http://www.midwestsupplies.com/flared-washer-for-cold-plate-fittings.html

Wing Nuts make attaching a tail piece to a shank easy. Or, use them when attaching tubing to a pump. There are a lot of uses for wing nuts in brewing. Plus, you can hand tighten these nuts instead of having to use a wrench.

http://www.midwestsupplies.com/wing-nut.html