On Orders Over $30

Text Us 952-260-4404

6" Boil Screen

More Views

6" Boil Screen


Stainless mesh tube replaces a false bottom in a mash tun or boil kettle for lautering wort or filtering whole hops. Overall length is 12.5 inches; 1/2" male pipe threads.

Free Shipping on Orders Over $30



Stainless mesh tube replaces a false bottom in a mash tun or boil kettle for lautering wort or filtering whole hops. Overall length is 6.5 inches; 1/2" male pipe threads.

Please note: This product requires the 1/2" Adapter for IsoFlow™ and EZ Clean™ Bulkheads in order to be compatible with IsoFlow™ or EZ Clean™ hardware.
Details & Instructions

Additional Information

Diameter 1"

4.7 / 5.0
19 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
Good screen
I had this attached to a Weldless Kettle Conversion on the inside of an 8Gal brew kettle and it has filtered out virtually every remnant of the pellatized hops I've used. It struggled with my pumpkin ale, but that's because of the pumpkin and not a defect with the screen. It works great and the 6" is a perfect size for my brew kettle. I do have to be careful when I'm stirring my wort though so I don't run my brewing utensils into the mesh. Although, it seems sturdy enough that it could probably take a minor beating during a typical brew._x000D__x000D_The screen was attached to a threaded adapter as shown in the picture but when I tried to unscrew it from the Weldless conversion piece, the filter came off the threaded adapter. It's not a huge issue because now I just 're-screw' it onto the threaded adapter and it holds and filters just fine. I remove it from the threaded adapter to clean and reinstall it for my next brew day. If this happens to yours, be careful because the cut pieces of mesh are SHARP and I can't imagine blood being good for a sanitary brew area._x000D__x000D_Because it came off the threaded adapter, I knocked it 1 point in quality, but not because I'm upset with the product. I've worked around it. However, in order for it to be 'perfect' quality, it would have had to not come off the threaded adapter after the first boil._x000D_
October 29, 2012
Quality kettle screen
Perfect size for a 5 gal converted cooler mash tun.
December 28, 2015
Good sturdy screen
I bought this for a cooler mash tun. It is well built and sturdy i.e., wil not colapse under the weight of your grain.
July 12, 2012
I picked up two of these bad boys! One for my brew kettle to help cut down on the amount of hops and other particulates that make it into my primary. And the other for my partial mash cooler so I don't have to transfer the grains and can sparge right through the cooler. Nice product for a great price!
November 27, 2012
WORKS Great.
I just slid it on the original spicket inside a 5 gallon igloo cooler and it works great.
September 27, 2017
1 year ago
Top notch product!
I purchased this to install in a 2 gallon Coleman cooler in order to convert it to a mash tun for 1 gallon batches. It fits perfectly into the cooler with a standard cooler bulkhead and works like a charm! As the description says, it's heavy duty and I have no concern that this screen could stand up to a full 5 gallon or greater batch. With the screen installed, I ended up with about 0.2 gallons of deadspace, though with a small cooler, it's easy to flip it and drain out the remaining wort. _x000D__x000D_I would highly recommend this screen to anyone looking for a mini mash tun conversion project!
December 29, 2012
great product !
I bought a ss false bottom for my 5 gal mash tun cooler and it did not fit, sent it back to NB. Found this screen here at Midwest and brewed a AG batch last night. It worked like a champ,I am very happy. Save your money and buy this instead of a SS false bottom.
February 4, 2013
Perfect for a boil screen
Nice, rigid stainless mesh that seems like it'll last. Fit on my kettle outlet valve with the addition of a stainless 1/2" NPT coupler.
February 22, 2013
Get clean clear beer
I use this inside my brew kettle to filter out everything I don't want in my finished Wort. Filters great, strong, and easy to clean.
March 5, 2013
Works Great
Works as advertised. Great for using in boil pot to strain out particulate before a plate chiller. Just make sure your kettle valve is 1/2" female threaded (some weldless valves on the market have a 3/8" connection).
March 13, 2013
Customer Q&A
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 6 answers
Will your 6" boil screen connect to this valve without any adapters?
A shopper on Mar 9, 2017
6" Boil Screen
Stainless Steel Cooler Valve with Barb
Stainless Steel Cooler Valve with Barb
BEST ANSWER: it connects without an adapter to the WELDLESS BULKHEAD FITTING
which is included with that valve assembly and the kettle conversion one.

Call Us 888-449-2739

Text Us 952-260-4404

Please wait...

Your selected product has been added to your Cart.

Continue Shopping Go To Cart