- Description
-
Details
Use a 1/4" Stainless Beer Tail Piece in conjunction with a chrome plated hex or wing nut when attaching to a keg coupling or shank that does not have a welded nipple attached. - Details & Instructions
-
Additional Information
- Reviews
-
4.9 / 5.09 ReviewsNicer than brassOver the last year I've switched my beer lines to SS. While I keep a few washers on hand I've never needed to use them.
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
March 17, 2014- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Clean it well then it's goodI too noticed some small metal bits. I cleaned it well and have been using it since. Its convenient to to attach the liquid hoses to shanks in a kegging setup.- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
February 28, 2014- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Very useful!If you like to switch out your home brew keg for a commercial keg, this could be an essential piece for your setup. Add the hex nut and washer and this is an easy low cost way to attach your gas or liquid line to the keg tap. Also works great for attaching a shank without a barbed tail.- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
December 17, 2013- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Stainless steelI use these for my hose connections. All my lines use stainless where I can , not brass.- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
December 5, 2013- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Clean well before usingThere were some small speck of metal that would have interefered with the seal had I not thoroughly cleaned the tail piece. It now works as it should.- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
September 11, 2013- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Threading--mehMake sure to take apart and clean well- some small pieces/shavings in between pieces. Check threading as well as final seal before going into full usage.- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
April 5, 2013- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Stainless is great!I switched all of my beer lines to stainless and really enjoy the stainless over the standard. I keep a few extra washers around but have never needed to use a new washer.- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
February 27, 2013- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Very UsefulGreat product for attaching beer line to shank. Solid and well made.- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
February 17, 2013- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
StainlessWorks great to attach liquid hose to shanks in a kegging setup. Make sure to use a washer with the washer. Stainless is great compared to brass.- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
December 16, 2012- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Customer Q&A
-
Start typing your question and we'll check if it was already asked and answered. Learn More
You may also be interested in the following product(s)
-
1/4" Stainless MFL Tail Piece
$8.99 -
1/4" Barbed Tail Piece
Regular Price: $1.13
Special Price $0.33
-
Cold Plate Fittings, Out 1/4" Barb
$5.99 -
Wing Nut
$6.99